INSTALLATION AND ADHESIVES

POSA E COLLA

THE SUBSTRATE

The floor substrate must be resistant enough to bear the expected stress and weight added with the ceramic tiles, it must be

perfectly planar, perfectly aged (aged 28 days or according to the manufacturer’s specifications) and dry, and free of any lose

part such as oil, water, dust, paint, grease etc., which might compromise the adhesion of the slabs.

REINFORCED CONCRETE SUBSTRATE

The substrate must be aged, cured, clean, dry and free of any substance which might compromise the adhesion of the ceramic.

Any crack due to hygrometric shrinkage must be sealed using a two-component epoxy fluid adhesive (ie. EPORIP by Mapei

or similar). If the concrete support is dirty or has surface dust it must be thoroughly cleaned and the a suitable single-compo-

nent resin primer with a very low content of colatile organic compounds (VOC) must be applied (ie. PRIMER G or ECO PRIM

T by Mapei spa or similar). If the concrete surface has any surface inconsistencies it must be consolidated with a suitable

single-component or two-component epoxy or polyurethane primer (such as PRIMER MF or ECOPRIM PU 1K by Mapei spa or

similar).

SCREED COATS

The screed surface must be aged (aged 28 days or according to the manufacturer’s specifications), cured, clean, dry and free of

any substance which might compromise the adhesion of the ceramic. Any crack due to hygrometric shrinkage must be sealed

using a two-component epoxy fluid adhesive (ie. EPORIP by Mapei or similar). Once the surface is completely cured it is impor-

tant to check that it is strong enough to bear the weight of the ceramic that will be fixed on it. If the concrete support is dirty

or has surface dust it must be thoroughly cleaned and the a suitable single-component resin primer with a very low content

of colatile organic compounds (VOC) must be applied (ie. PRIMER G or ECO PRIM T by Mapei spa or similar). If the concrete

surface has any surface inconsistencies it must be consolidated with a suitable single-component or two-component epoxy or

polyurethane primer (such as PRIMER MF or ECOPRIM PU 1K by Mapei spa or similar). For floor heating installations the cor-

rect switch on cycle of the system must be performed in compliance with the applicable standards and the indications of the

manufacturer of the floor heating system.

EXISTING CERAMICS OR STONE FLOORINGS

For ceramic and stone floorings, check that the existing covering is perfectly attached to the support, planar and free of any

cracks or sections that tend to detach from the substrate. If not proceed as follows:

• seal the floor cracks with two-component fluid epoxy resins (such as EPORIP by Mapei spa or similar);

• fill any gaps created when removing any tiles or slabs that do not adhere, using rapid setting thixotropic smoothing com-

pounds (such as ADESILEX P4 or NIVORAPID by Mapei spa or similar);

• correct any planarity imperfections with levelling mortars, after cleaning the existing surface and, if necessary, using a sui-

table primer (such as ECO PRIM T by Mapei spa or similar ).

Generally speaking existing ceramic or stone floorings must be suitably cleaned with a solution of warm water and caustic

soda at 20%, and rinsed thoroughly to remove any trace of loose substances. In specific cases the surface can be subjected to

some surface abrasion to achieve a rough and clean support, in order to improve the subsequent adhesion.

TILES INSTALLATION

Before laying Gigacer slabs select the most suitable adhesive according to the type of support, the final environment, the we-

ather conditions of the site and the time available between laying and use. The table below lists a few examples of adhesive

systems suitable for laying our slabs on horizontal indoor surfaces.

SUGGESTED ADHESIVES

Ardex - Mapei - Kerakoll

For a perfect installation and a complete wetting we suggest to apply the adhesive with double spreading, applying the glue

both on the substrate and on the back of the tile. We suggest to use this procedure especially for 4,8 mm and 6 mm slabs.

Apply the adhesive with an adequately sized notched trowel, firstly laying one thin layer on the support with the flat edge of

the trowel and then applying the desired thickness with the notched edge. Then apply the adhesive on the substrate with a

notched trowel and lay the tile. Beat the tile with a rubber hammer to ensure perfect wetting and remove any air bubble which

might have generated between the tile and the substrate. It is possible to use systems such as Tuscan Leveling or similar to

help maintaining the perfect planarity of the floor.

GROUTING

We suggest to use 2 mm joints in case of multi-format flooring and 2-4 mm in case of single-format. Please read carefully our

technical specifications charts and apply the necessary dilatation joints. The joints must be grouted only after the adhesive has

hardened, normally 3 hours for fast set adhesives and at least 24 hours for regular set adhesives. These values refer to laying

carried out at +23°C and 50 % relative humidity.

222

IL SUPPORTO

Il massetto o il substrato deve essere sufficientemente resistente a sopportare il peso aggiuntivo previsto con l’installazione del

pavimento in ceramica, deve essere perfettamente planare, perfettamente maturo (da 28 giorni di presa o secondo indicazioni del

produttore del cemento) e libero da qualsiasi detrito o liquido sulla superficie (polvere, sabbia, terra, olio, vernice, grasso, ecc.) che

possa compromettere l’adesione della ceramica al supporto.

SUPPORTI IN CEMENTO RINFORZATO

Il supporto deve essere maturo, pulito, asciutto e libero da qualsiasi sostanza che possa compromettere l’adesione della ceramica

al substrato. Ogni crepa formatasi a seguito del restringimento idrometrico del supporto deve essere sigillata con adesivo bicom-

ponente epossidico (es. EPORIP di Mapei spa o simili). Se il supporto presenta tracce di polvere o sporco deve essere pulito accu-

ratamente e successivamente deve essere applicato uno strato di primer in resina monocomponente con contenuto di componenti

organici volatili (VOC) molto basso (es. PRIMER G o ECO PRIM T di Mapei spa o simili). Se la superficie del cemento presenta par-

ti scrostate o indebolite è necessario consolidarle con un primer epossidico o in poliuretano mono o bicomponente (come PRIMER

MF o ECOPRIM PU 1K di Mapei spa o simili).

MASSETTI

Il massetto deve essere maturo (28 giorni di presa o secondo indicazioni del produttore del cemento), pulito, asciutto e libero da

qualsiasi sostanza che possa compromettere l’adesione della ceramica al substrato. Ogni crepa formatasi a seguito del restrin-

gimento idrometrico del supporto deve essere sigillata con adesivo bicomponente epossidico (es. EPORIP di Mapei spa o simili).

Una volta che la superficie è completamente liscia e matura è necessario controllare che abbia la resistenza necessaria a soppor-

tare le sollecitazioni e il peso ai quali sarà sottoposta con la posa della ceramica. Se il supporto presenta tracce di polvere o sporco

deve essere pulito accuratamente e successivamente deve essere applicato uno strato di primer in resina monocomponente con

contenuto di componenti organici volatili (VOC) molto basso (es. PRIMER G o ECO PRIM T di Mapei spa o simili). Se la superficie

del cemento presenta parti scrostate o indebolite è necessario consolidarle con un primer epossidico o in poliuretano mono o bi-

componente (come PRIMER MF o ECOPRIM PU 1K di Mapei spa o simili). Per pavimenti riscaldati deve essere eseguito il corretto

ciclo del sistema in conformità con le norme vigenti e le indicazioni del produttore del sistema di riscaldamento a pavimento.

PAVIMENTI ESISTENTI IN CERAMICA, COTTO O PIETRA

Per il fissaggio delle lastre su pavimenti esistenti controllare per prima cosa che il pavimento esistente sia ancora solidamente

attaccato al substrato, che sia planare e non siano presenti rotture o parti distaccate. Se queste condizioni non sono interamente

soddisfatte procedere come segue:

• Sigillare le crepe e le rotture con una resina epossidica bicomponente (come EPORIP di Mapei spa o simili)

• Riempire i vuoti lasciati da eventuali pietre o piastrelle rimosse usando un prodotto livellante (come ADESILEX P4 o NIVORAPID

di Mapei spa o simili)

• Correggere ogni imperfezione di planarità con malte livellanti dopo aver pulito la superficie e aver usato, se necessario, un pri-

mer (come ECO PRIM T di Mapei o simili).

In generale i pavimenti esistenti in ceramica o pietra naturale devono essere accuratamente puliti con una soluzione di acqua tie-

pida e soda caustica al 20%, e sciacquati abbondantemente per rimuovere ogni traccia di sostanza. In alcuni casi la superficie può

essere sottoposta ad abrasione, per ottenere un supporto più ruvido e aumentare l’aderenza delle colle.

LA POSA

Prima di installare le lastre Gigacer occorre selezionare l’adesivo più adatto a seconda del tipo di supporto, delle condizioni clima-

tiche e del tempo che intercorrerà tra la posa e l’inizio dell’utilizzo della superficie calpestabile. La tabella seguente illustra alcuni

esempi di adesivi adatti alla posa delle lastre Gigacer, sia di 12 mm che di 4,8 mm di spessore.

ADESIVI CONSIGLIATI

Ardex - Mapei -Kerakoll

Per una posa perfetta e una completa bagnatura consigliamo, soprattutto in caso di utilizzo delle lastre sottili in 4,8 mm e 6 mm,

di effettuare la doppia spalmatura, applicando la colla sia sul retro della lastra che sul supporto. Applicare prima uno strato sottile

di colla sul retro della lastra con una spatola liscia, e di seguito applicare altro adesivo stendendolo con una spatola dentata effet-

tuando movimenti semicircolari. Applicare poi la colla sul sottofondo con una spatola dentata e posare la lastra. Battere la lastra

con un martello di gomma per assicurarsi della perfetta bagnatura e scongiurare la presenza di vuoti d’aria. È possibile utilizzare

sistemi per agevolare la perfetta planarità della posa, soprattutto con lastre di grande formato, come ad esempio il Tuscan Leve-

ling System.

STUCCATURA

Consigliamo una fuga di 2 mm in caso di posa multiformato e 2-4 mm in caso di posa di un formato unico. È necessario consul-

tare le nostre tabelle di caratteristiche tecniche e applicare i giunti di dilatazione necessari. Lo stucco deve essere applicato solo

dopo che l’adesivo si sia indurito, normalmente dopo 3 ore in caso di adesivo rapido e dopo 24 ore in caso di adesivo standard.

Questi valori si riferiscono ad una posa all’asciutto effettuata a una temperatura di +23°C e con il 50% di umidità relativa.