Tutti i comandi termostatici ad alta portata possono essere installati in verticale
(con entrate dell’acqua calda e fredda rivolte verso il basso) o in orizzontale (con
entrate dell’acqua calda e fredda rivolte verso il lato destro).
Blocco di sicurezza a 38 °C
Temperatura minima di esercizio: 3°C FREDDA (consigliata 15°C)
Temperatura massima di esercizio: 80°C CALDA (consigliata 65°C) Differenziale
termico consigliato: 50°C
Pressione minima di esercizio: 0.5 bar
Pressione massima di esercizio: 5 bar (per pressioni superiori si raccomanda di
installare un limitatore di pressione)
Pressione d’esercizio consigliata: 3 bar
Sistema di sicurezza con blocco dell’erogazione, in caso di mancanza di una
delle due acque
Dotati di filtri in acciaio inox per il trattenimento delle impurità
1) Tutte le uscite sono indipendenti (si possono aprire in contemporanea – in
questo caso, logicamente, la portata si ripartisce su tutte le vie aperte).
2) I rubinetti singoli presentano l’erogazione dell’acqua verso destra (o verso
l’alto se installati in orizzontale).
3) I termostatici da 1 a 4 uscite presentano tutte le vie di erogazione dell’acqua
verso destra (o tutte verso l’alto se installati in orizzontale).
4) A 3 bar, le portate per una singola uscita sono di 40 l/min circa.
FUNZIONAMENTO:
Sia con scaldabagni a gas che elettrici ad accumulo
Impianti centralizzati
Caldaie murali e da terra ad accumulo
ATTENZIONE:
Si consiglia, di contattare il proprio termoidraulico di fiducia per una corretta
e funzionale installazione del miscelatore termostatico, sia con i dispositivi di
riscaldamento sopraelencati, che con altre tipologie.
Leva in posizione ore 12 = deviatore chiuso. Ruotando verso destra o sinistra
si attivano le diverse uscite. Partendo dalla posizione di STOP, durante la
rotazione la portata dell’acqua si incrementa verso la posizione successiva.Tra
2 uscite adiacenti durante la rotazione diminuisce la portata dell’uscita iniziale
ed incrementa quella della successiva. In posizione intermedia sono entrambe
attive a pari portata.
SCHEME OPERATING THERMOSTATIC MIXER 2/3/4 OUT
Lever to the 12 o’clock position = switch closed. Turning left or right. They activate
different outputs. Starting from the STOP position, while rotation of the water flow rate
between two adjacent outputs is increased towards the next position. Between two
adjacent outputs during the rotation decreases the initial output flow and increases that
of the next. In position intermediate are both active at the same flow rate.
DEVIATORI 2/3 USCITE: Leva in posizione ore 12 = deviatore chiuso. Ruotando verso
destra o sinistra si attivano le diverse uscite. Partendo dalla posizione di STOP, durante
la rotazione la portata dell’acqua si incrementa verso la posizione successiva.Tra 2 uscite
adiacenti durante la rotazione diminuisce la portata dell’uscita iniziale ed incrementa
quella della successiva. In posizione intermedia sono entrambe attive a pari portata.
DEVIATORI 5 USCITE: Questi deviatori non hanno funzione di chiusura. Ruotando verso
destra o sinistra si attivano le uscite. Tra 2 uscite adiacenti durante la rotazione diminu-
isce la portata dell’uscita iniziale ed incrementa quella della successiva. In posizione
intermedia sono entrambe attive a pari portata.
SCHEME OPERATION SWITCHES FLUSH OUTPUT 2/3/5 3/4”
SWITCHES FLUSH OUTPUT 2/3: Lever to the 12 o’clock position = switch closed.
Turning left or right. They activate different outputs. Starting from the STOP position,
while rotation of the water flow rate between two adjacent outputs is increased towards
the next position. Between two adjacent outputs during the rotation decreases the initial
output flow and increases that of the next. In position intermediate are both active at
the same flow rate.
SWITCHES FLUSH OUTPUT 5: These diverters have not closing function. By turning
to the right or left activates the outputs. Between two adjacent outputs during the
rotation decreases the initial output flow and increases that of the next. In position
intermediate are both active at the same flow rate.
HIGH RATE THERMOSTATIC MIXER
All high rate thermostatic mixer can be installed in vertical (with hot and cold water
inlets pointing down) or horizontally (with hot and cold water directed toward the
right side).
Safety block at 38° C
Minimum working temperature 3°C COLD WATER (suggested 15°C)
Maximum working temperature 80°C HOT WATER (suggested 65°C)
Suggested temperature differential: 50°C
Minimum pressure of working: 0.5 bar
Maximum operating pressure: 5 bar (For higher hydraulic pressures we recommend
to install a pressure reducer)
Pressure of working advised: 3 bar
Safety system with water supply block in case either hot or cold water is missing
Supplied with steel filter to keep the impurity out
FEATURES OF HIGH CAPACITY THERMOSTATIC MIXERS FROM 1 TILL 4 EXITS
WITH OPTION OF ONE OR SEPARATE RESTRICTED WALL CONTROLS
1) All the outflows are unconnected (they can be open at the same time – obviously in
this case the water-flow capacity divides onto all the open ways).
2) The single taps have the water-flow towards the right hand-side (or towards the top
if they are sep up in the horizontal position).
3) The thermostatic mixers with one/four outflows have all the water-flow gateways
towards the right hand-side (or all the gateways towards the top if they are set up in
the horizontal position).
4) To three bars, the single gateway water-flow capacities are about 40 l/min.
INSTRUCTIONS:
It works both with electrical and gas water heater
Central heating systems
Wall and floor boiler
ATTENTION:
It is strongly recommended that the product is only installed by a fully qualified
plumber who is aware of the installation and the pressure requirements of the system
(both for the heating systems above mentioned and others).
REVIVRE
COMANDI
OVALE