I Frammenti Vetro

Design

Claudio Silvestrin

CONSIGLI PER LA POSA

LAYING GUIDE

CARATTERISTICHE TECNICHE

TECH INFO

1. CONTROLLO MATERIALE

Controllare che il materiale sia sufficiente per completare il lavoro. In caso contrario

ordinare materiale della stessa partita (stesso tono e produzione).

2. RASATURA DELLA PARETE

Il sottofondo deve essere perfettamente rasato (liscio) e uniforme in quanto il mo-

saico, avendo dimensioni ridotte, legge anche le più piccole asperità del sottofondo.

3. STESURA DEL PRIMER

Prima di applicare la colla, stendere sulla parete (o pavimento) un Primer scelto tra

quelli attualmente in commercio. Tale operazione, rallentando l’indurimento della col-

la, consente di stendere il collante su di una più ampia superficie (e di utilizzarne una

più modesta quantità).

4. STESURA DEL COLLANTE

Preparare il collante LITOELASTIC e stenderne un primo strato utilizzando la parte

liscia di una spatola per Pvc con dente triangolare da 2mm (ART. 112/D V2). La quan-

tità deve essere tale da consentire la posa di oltre un metro quadro di materiale.

Pettinare con attenzione la colla ed evitare risalite di adesivo nello spessore della

fuga: tali risalite interferiscono con la colorazione finale dello stucco. Anche eventuali

discontinuità durante la stesura dell’adesivo possono, a stuccatura ultimata, essere

visibili: fare attenzione.

5. POSA DEL MATERIALE

Estrarre i fogli dalla confezione solamente prima della posa. Maneggiare i fogli con

cura. La lavorazione deve avere luogo in ambienti con temperature che vanno da un

minimo di 5 a un massimo di 30 gradi centigradi. Posare il materiale verificando che

la distanza tra i fogli sia la stessa di quella che esiste tra un tassello e l’altro. Una volta

posato il foglio alla parete non è più possibile rimuoverlo.

6. BATTITURA DEL MATERIALE

Terminata la posa, battere il materiale con la spatola in ferro (e non con il frettazzo in

gomma) e massaggiare con le dita i bordi là dove il materiale tende ad alzarsi anche

dopo la battitura. Questa importante operazione fa si che non si legga il modulo del

foglio.

7. REGISTRAZIONE DEL MATERIALE

Ultimata la posa e prima dell’asciugatura della colla regolare, dove serve, la distanza

tra le tessere alfine di uniformare tutte le fughe.

8. RIMOZIONE PELLICOLA

A completa asciugatura del collante, 48/72 ore in base alla temperatura ed all’u-

midità del luogo, rimuovere la pellicola iniziando da uno dei vertici, con movimento

diagonale. E’ fondamentale che la pellicola non faccia eccessiva resistenza durante

il distacco. Qualora la pellicola presenti tale problematicità si consiglia di scaldare

il film alfine di diminuire la presa della colla sulle tessere. Una volta tolta la pellicola

potrebbero restare attaccate alcune tessere alla stessa. Nel caso si consiglia di at-

taccarle con del semplice silicone a presa rapida. Qualora si voglia utilizzare la stessa

colla di applicazione occorre farla asciugare prima della stesura dello stucco.

9. RIMOZIONE COLLA IN ESUBERO

Prima dell’operazione di stuccatura rimuovere dove serve la colla fuoriuscita dalle

fughe e passare leggermente con una spugna umida alfine di togliere gli eventuali

depositi di colla.

10. STUCCATURA DEL MATERIALE

Prima della stuccatura assicurarsi che le fughe siano perfettamente asciutte. Uti-

lizzare lo stucco/sigillante STARLIKE CRYSTAL o COLOR CRYSTAL. Si raccomanda

di non aggiungere acqua o solventi per migliorare la lavorabilità del prodotto. Dopo

aver applicato il prodotto all’interno delle fughe mediante l’apposita spatola gomma-

ta asportare il prodotto in eccesso con la stessa. Eventuali riprese di materiale nelle

fughe vanno effettuate prima della pulizia con acqua onde evitare la formazione di

cristalli bianchi sulla superficie. Nel caso di applicazione a parete si raccomanda di

stendere il sigillante/stucco realizzando fasce verticali complete prima di procedere

alla fase di pulizia.

11. PULIZIA DEL MATERIALE

Durante la fase di pulizia evitare che l’acqua finisca nelle fughe ancora vuote uti-

lizzando quantità d’acqua non eccessive ed evitando in questo modo ristagni sulla

superficie delle fughe ancora fresche. Eventuali aloni o residui di prodotto traspa-

rente possono essere rimossi dalla superficie di mosaico a distanza di circa 24 ore o

comunque dopo l’indurimento delle fughe (a seconda delle temperature) utilizzando i

detergenti specifici LITONET (pavimentazioni) o LITONET GEL (rivestimenti).

1. CHECK YOUR MATERIAL

Make sure you have enough material to finish the job. If not, order material from the

same batch (same tone and production run).

2. SHAVING THE WALL

The foundation must be completely shaved (smooth) and even. Mosaics are small

which means they will show up even the slightest roughness on the surface under-

neath.

3. APPLYING THE PRIMER

Before applying the glue, apply a primer currently available on sale on the wall (or on

the floor). As this delays the hardening, the glue can be applied on a larger surface

(and coverage increases consequently).

4. APPLYING THE GLUE

Prepare the glue and apply the first layer, using the smooth part of the spatula. You

must use enough to allow the laying of about more thanone square metre of material.

Use a comb spatula with teeth 3 mm wide and 2,5 mm high to apply the adhesive.

5. LAYING THE MOSAICS

Remove the sheets from the packaging just before the tiles are laid. Handle the she-

ets with care. Application should take place in environments with a minimum tempe-

rature of 5 degrees celsius and a maximum of 30. When laying the product make sure

that the distance between the sheets is equal to that between the squares.

Once the sheets are laid the sheet cannot be removed from the wall.

6. SMOOTHING THE MOSAICS

After laying, smooth the mosaics with the iron spatula (not the rubber scraper) and

using your fingers, press the edges of the material where it tends to rise up even after

smoothing. This important step ensures that you cannot see the join of the sheet.

7. FIXING THE MOSAICS

Once laying is complete, and before the adhesive dries, where necessary, adjust the

distance between tiles so that all the joins are the same.

8. REMOVING THE FILM

Once the adhesive has dried, 48/72 hours according to the temperature and hu-

midity of the place, remove the film, starting at one of the top corner, with diagonal

movement. It’s a crucial that the film does not offer too much resistance when trying

to strip it off.Once the film has been removed, some squares could remain attached

to the film. In this case we recommend attaching them with fast-drying silicon. If you

want to use the same adhesive used to apply the sheets, ensure that the adhesive on

the wall has dried before you apply the remaining squares.

9. REMOVING EXCESS GLUE

Before the application of the grout, remove excess adhesive and use a moist sponge

to wipe off any remaining adhesive.

10. GROUTING

Before grouting, make sure the joints are perfectly dry. Use STARLIKE CRYSTAL or

COLOR CRYSTAL grout/sealant. It is recommended not to add water or thinners to

improve the product workability. After applying the product inside the joints with the

suitable rubber-coated spatula, use it again to remove any excess. Possible tou-

ch-ups of material in the joints must be made before cleaning with water to prevent

white crystals from forming on the surface. In wall applications it is recommended to

spread the grout/sealant making complete vertical stripes before cleaning.

11. CLEANING

While cleaning, prevent the water from entering in the still empty joints using a small

amount of water and thus preventing stagnation on the surface of still wet joints.

Possible halos or residues of transparent product can be removed from the mosaic

surface after approx. 24 hours or anyway after the joints have hardened (depending

on the temperature), using the specific detergents LITONET (floors) or LITONET GEL

(walls).

Catalogue 2017

36

Micro.

37

CONSUMO DI STUCCO KG/MQ 3,30 KG

GROUT REQUIRED KG/ S

Q

M 3,30 KG