Micromosaics

1. CONTROLLO MATERIALE

Controllare che il materiale sia sufficiente per completare il lavoro.

In caso contrario ordinare materiale della stessa partita (stesso

tono e produzione).

2. RASATURA DELLA PARETE

Il sottofondo deve essere perfettamente rasato (liscio) e uniforme

in quanto il mosaico, avendo dimensioni ridotte, legge anche le più

piccole asperità del sottofondo.

3. STESURA DEL PRIMER

Prima di applicare la colla, stendere sulla parete (o pavimento) un Primer

scelto tra quelli attualmente in commercio. Tale operazione, rallentando

l’indurimento della colla, constente di stendere il collante su di una più

ampia superficie (e di utilizzarne una più modesta quantità).

4. STESURA DEL COLLANTE

Preparare il collante e stenderne un primo strato utilizzando

la parte liscia della spatola. La quantità deve essere tale da

consentire la posa di oltre un metro quadro di materiale. Con una

spatola avente una dente di 3 mm di larghezza e 2,5 mm di altezza

pettinare con attenzione la colla mediante una doppia spalmatura:

sia la superficie da rivestire che il retro del foglio di mosaico.

5. PREPARAZIONE DEL MATERIALE (solo per Micromosaics.)

Per una posa davvero ottimale, si possono eventualmente rifilare i

fogli di mosaico asportando/tagliando la fila di cubetti più esterna

di ognuno dei quattro lati del modulo (non obbligatorio).

6. POSA DEL MATERIALE

Posare il materiale sfalsando i fogli in modo casuale verificando

che la distanza tra i fogli sia le stessa di quella che esiste tra un

tassello e l’altro.

7. BATTITURA DEL MATERIALE

Terminata la posa, battere il materiale con la spatola in ferro (e

non con il frettazzo in gomma) e massaggiare con le dita i bordi là

dove il materiale tende ad alzarsi anche dopo la battitura. Questa

importante operazione fa si che non si legga il modulo del foglio.

IMPORTANTE: Prima di battere il materiale verificare che la colla

abbia iniziato ad asciugarsi staccando uno spigolo qualsiasi del

foglio di mosaico dal muro. Quando questa operazione diventa più

difficoltosa è il momento di iniziare a battere il materiale.

8. REGISTRAZIONE DEL MATERIALE

Ultimata la posa e prima dell’asciugatura della colla regolare, dove

serve, la distanza tra le tessere al fine di uniformare tutte le fughe.

Questa operazione viene fatta tagliando la rete con un taglierino

e muovendo le tessere con un cazzuolino o altro strumento

sufficientemente sottile.

9. RIMOZIONE COLLANTE

Eventuali tracce di adesivo presenti sulla superficie del mosaico

devono essere rimosse prima del suo completo indurimento

utilizzando una spugna inumidita.

Consigli per la posa

Laying guide

1. CHECK YOUR MATERIAL

Make sure you have enough material to finish the job. If not,

order material from the same batch (same tone and production

run).

2. SHAVING THE WALL

The foundation must be completely shaved (smooth) and even.

Mosaics are small which means they will show up even the

slightest roughness on the surface underneath.

3. APPLYING THE PRIMER

Before applying the glue, apply a primer currently available on

sale on the wall (or on the floor). As this delays the hardening,

the glue can be applied on a larger surface (and coverage

increases consequently).

4. APPLYING THE GLUE

Prepare the glue and apply the first layer, using the smooth part

of the spatula. You must use enough to allow the laying of about

more than one square metre of material. Use a comb spatula

with teeth 3 mm wide and 2,5 mm high to apply the adhesive,

spreading two layers: one on the surface to be tiled and one on

the back of the mosaic sheet.

5. PREPARING THE MATERIAL (only for Micromosaics.)

For the best fixing, the mosaic sheets can be possibly trimmed by

removing/cutting the most external row of cubes in each of the

four sides (not mandatory).

6. LAYING THE MOSAICS

Lay the mosaic by staggering the pieces in a casual way, taking

care that the distance between sheets is the same as the distance

between one mosaic tile and the next.

7. SMOOTHING THE MOSAICS

After laying, smooth the mosaics with the iron spatula (not the

rubber scraper) and using your fingers, press the edges of the

material where it tends to rise up even after smoothing. This

important step ensures that you cannot see the join of the sheet.

IMPORTANT: Before tapping the mosaic down, check that the

adhesive has begun to set by pulling up any corner of the mosaic

sheet from the wall. The time to begin tapping the mosaic is when

it starts to become difficult to detach the sheet.

8. FIXING THE MOSAICS

Once laying is complete, and before the adhesive dries, where

necessary, adjust the distance between tiles so that all the joins

are the same. You should do this by cutting the mesh with a cutter

and moving the tiles with a small trowel or other sufficiently fine

instrument.

9. REMOVING THE GLUE

Any traces of glue left on the surface of the mosaic must

be removed before it dries completely, using a damp

sponge.

Catalogue 2022

184