Carpenteria

Tutte le unità della serie i-Max sono prodotte in lamiera zincata a caldo e

verniciata dopo lavorazione con polveri poliuretaniche in forno a 180°C

per assicurare la migliore resistenza agli agenti atmosferici.

Controllo V.415

Nuova logica di controllo e interfaccia display installata su tutte le unità

Maxa di nuova generazione i-MAX. Consente una rapida manutenzione

con aggiornamento parametri e firmware da periferica USB. Incremento

della memoria con implementazione di nuove logiche

V.415 control board

New control logic and display interface installed on all new Maxa units

generation i-MAX. Allows rapid maintenance with parameter and firmware

updates from USB device. By the implementation of new logics it permit

the increase of memory.

Ventilatore

Il ventilatore è realizzato in materiale plastico caricato con fibra, è

di tipo assiale con pale a profilo alare.

è bilanciato staticamente e

dinamicamente e fornito completo di griglia di protezione e boccaglio.

Il motore elettrico utilizzato è modulato tramite inverter, direttamente

accoppiato ed equipaggiato di protezione termica integrata. Il motore

ha un grado di protezione IP 54 secondo la CEI EN 60529.

Circuito Frigorifero

I circuiti frigoriferi sono realizzati utilizzando componenti di primarie

aziende internazionali e secondo la normativa UNI EN 13134 riguardante

i processi di saldo-brasatura. Il gas refrigerante utilizzato è R410A. Ogni

circuito frigorifero include nella sua versione base: valvola inversione

ciclo a 4 vie, valvola di espansione elettronica, separatore di liquido,

ricevitori di liquido, circuito ausiliario per ridurre i tempi di sbrinamento,

circuito recupero olio, valvole di non ritorno, valvole di ispezione per

manutenzione e controllo, dispositivo di sicurezza secondo normativa

PED (pressostato di alta pressione), trasduttori di pressione, sonde di

precisione, filtro deidratatore ad alta capacità, filtri meccanici .

Refrigerant Circuit

The refrigerant circuit has been manufactured by means of international

primary brands components and according to the UNI EN 13134 Rule

concerning welding procedures. The refrigerant gas is R410A. Each

refrigerant circuit includes 4 way reverse cycle valve, electronic expansion

valve, liquid separator, liquid receivers, auxiliary circuit to reduce the

defrosting time, oil recovery circuit, non-return valves, valves of inspection

for maintenance and control, safety device (high pressure switch)

according to PED regulation, pressure transducers, precision sensors,

high capacity filter dryer, mechanical filters.

Compressori

I compressori sono di tipo scroll, montati su antivibranti in gomma. Per

ognuno dei 2 circuiti è presente un compressore DC inverter. In questo

modo è possibile, in ogni circuito, modulare in continuo tra la potenza

minima del solo compressore inverter e la somma delle potenze massime

di tutti i compressori del circuito. Su tutte le unità è quindi possibile

parzializzare la potenza resa e quella assorbita fino al 9% della massima

sui modelli con 4 compressori e fino al 6% nei modelli a 6 compressori.

La resistenza del carter è di serie.

L’ispezione ai compressori è possibile attraverso il pannello frontale

dell’unità che permette la manutenzione anche con unità in funzionamento.

Compressors

The compressors are a scroll type, mounted on a rubber material acting

as a shock absorber. Each one of the two circuits is equipped with a

DC inverter compressor. In this way, the capacity of each circuit can

be modulated continuously between the minimum capacity of a single

inverter compressor and the sum of the maximum capacities of the whole

compressors of the same circuit. On all units of this series, the range of

partialization of the output capacity and the energy consumption can

reach the 9% of the maximum capacity for the models provided with 4

compressors and up to 6% for the models provided with 6 compressors.

The crankcase heater is standard equipment. The compressors can be

inspected through the frontal panel of the unit that allows the maintenance

of the compressors even if the unit is in operations.

Carpentry

The i-MAX chillers/heat pump units are made up of hot-galvanized sheet

metal, painted with polyurethane powder enamels at 180°C in order to

ensure the best resistance against atmospheric agents.

Fan Section

The type of the fan is axial-flow with aluminum aerofoil blades of fibre.

It is statically and dynamically balanced and supplied with fan grill for

protection and locking). The electric fan motor used in this series is

modulated by inverter, directly coupled and equipped with integrated

thermal protection. The protection class of the motors is IP X4 according

to CEI EN 60335-2-80 Rule.

A

I

R

C

O

N

D

I

T

I

O

N

I

N

G

Pompe di Calore & Gamma Industriale 2022

63

P

O

M

P

E

D

I

C

A

L

O

R

E