Indications for laying

INDICAZIONI PER LA POSA / INDICATIONS PUOR LA POSE / HINWEISE ZUR VRLEGUNG /

INDICACIONES PARA LA COLOCACIÓN / ИНСТРУКЦИИ ПО УКЛАДКЕ

EN PLANNING FOR SURFACES

To get the most from DOM floor and wall cladding, allowing the maximum

expression of its aesthetic and technical qualities, it is necessary to take into

account the factors that influence the installation, such as the intended use of the

environment, the loads, the mechanical, thermal, physical and chemical stresses

to which the tiles will be subjected, the dimensions of the environment and any

slopes present. Consequently, the specifications must include all the details

of the site: type and method of installation, width of the grout lines, necessary

expansion joints, perimeter joints, etc... When choosing tiles, it is also a good idea

to evaluate the technical requirements, the existing formats, the intended use and

the choice of the grout (grouts with strong or highly contrasting colours can make

cleaning more difficult when compared to a tone-on-tone grout).

Natural porcelain stoneware materials have slightly uneven dimensions,

so the installation will be carried out with a grout line between the tiles of:

• 2 mm for rectified materials;

• 3/4 mm for natural products.

DOM Ceramiche strongly advises against installations with zero grout lines and

suggests installation with a staggered tile at a maximum of 10%/20%.

THE INSTALLATION

Before starting the installation, it is advisable to lay down at least 2 or 3 square

metres of material to check the overall effect and take the material from multiple

boxes to obtain a better chromatic effect. The shading is a characteristic of some

ceramic products. The tiles must not be previously immersed in water, nor should

the operating surface be marked with pencils and/or felt-tip pens.

The installer will have to take note of any obvious defects (of article, quality,

tone, presence of steps or small differences in level with adjacent tiles, etc.)

and report them to the client and the designer, requesting authorisation before

continuing work as, once laid, the material can no longer be disputed. Therefore

it is recommended to start the installation in the presence of the client and the

designer. In the period between the end of the installation and the delivery to the

final client, the ceramic tiling must:

• be kept clean and free from cement, sand, mortar and any other material that

may cause stains and/or phenomena of superficial mechanical abrasion;

• protected from damage or contamination potentially caused by the

foreseeable presence of other construction professionals

(painters, electricians, carpenters, etc.).

EXAMINATION AND CHECKING OF THE TILING

The examination and checking of the tiling must be done by the final customer

in the presence of the installer and the site manager by means of a visual

examination involving observation with the naked eye (with glasses, if normally

used) of the surface at a distance of 1 m.

An “effect” that can only be detected with oblique lighting, and only at close

range, perhaps with the help of a magnifying glass, can not be considered a

“defect”. An “effect” becomes a “defect” when it is visible under the observation

conditions described above.

WARNING: DOM Ceramiche, does not accept claims for material already installed

due to defects which were clearly visible before installation (article, quality, shade,

caliber, curved surfaces, stains, etc.) and shall not assume responsibility for the

quality of the tiling work but only for the characteristics of the supplied material.

At the end of the installation it is always a good idea to keep some extra tiles for

any future repairs, or also to have a sample of the material available in the event

of a dispute.

IT PROGETTO DELLE SUPERFICI

Per valorizzare un pavimento e rivestimento DOM, consentendo la massima

espressione delle sue qualità estetiche e tecniche, è necessario tenere conto

di quei fattori che influenzano la posa in opera, come la destinazione d’uso

dell’ambiente, i carichi, le sollecitazioni meccaniche, termiche, fisiche e chimiche

alle quali le piastrelle saranno sottoposte, le dimensioni dell’ambiente e le

eventuali pendenze. Di conseguenza, il capitolato dovrà comprendere ogni

specifica del cantiere: tipo e modalità di posa, dimensione della fuga, eventuali

giunti di dilatazione, giunti perimetrali, etc... Nella scelta delle piastrelle si

consiglia di valutare anche i requisiti tecnici, i formati esistenti, la destinazione

d’uso e la scelta dello stucco (gli stucchi di colori forti o molto contrastati

possono rendere la pulizia più laboriosa rispetto a uno stucco tono su tono).

I materiali in gres porcellanato naturale presentano una leggera scalibratura,

per cui la posa sarà effettuata con una fuga tra le piastrelle di:

• 2 mm per i materiali rettificati;

• 3/4 mm per i prodotti naturali.

DOM Ceramiche sconsiglia tassativamente la posa a giunto unito e suggerisce

la posa a correre con piastrelle sfalsate al massimo 10%/20%.

LA POSA IN OPERA

Prima dell’inizio della posa si consiglia di stendere a terra almeno 2 o 3 m

2

di materiale per verificarne l’effetto d’insieme e prelevare il materiale

attingendolo da più scatole per ottenere un miglior effetto cromatico.

La stonalizzazione è una caratteristica propria di alcuni prodotti ceramici.

Le piastrelle non devono essere preventivamente immerse nell’acqua,

né devono essere segnate sulla superficie di esercizio con matite e/o pennarelli.

Il posatore dovrà far notare e segnalare al committente e al progettista la

presenza di eventuali difetti palesi (di articolo, qualità, tono, presenza di

gradini o piccoli dislivelli con le piastrelle adiacenti, etc.) chiedendo l’eventuale

autorizzazione a continuare il lavoro in quanto, una volta posato, il materiale non

sarà più contestabile. Quindi si raccomanda di dare l’avvio alla posa in presenza

del committente e del progettista. Nel periodo compreso fra la conclusione

della posa e la consegna al committente finale, la piastrellatura ceramica dovrà:

• essere mantenuta pulita e libera da cemento, sabbia, malta e da qualsiasi

altro materiale che possa causare macchie e/o fenomeni di abrasione

meccanica superficiale;

• protetta da danni o contaminazioni potenzialmente apportate a seguito

di una prevedibile frequentazione di altri operatori edilizi (imbianchini,

elettricisti, falegnami, etc.).

ESAME E CONTROLLO DELLA PIASTRELLATURA

L’esame ed il controllo della piastrellatura deve essere fatto dal committente

finale alla presenza del posatore e del responsabile del cantiere attraverso

un esame visivo con osservazione a occhio nudo (con gli occhiali, se di uso

abituale) della superficie ad una distanza di 1 mt. Un “effetto” rilevabile solo

con luce radente, e solo a distanza ravvicinata, magari con l’aiuto di una lente

di ingrandimento, non può essere considerato un “difetto”. Un “effetto” diventa

“difetto” quando è visibile nelle condizioni di osservazione sopra riportate.

AVVERTENZA: DOM Ceramiche, a materiale gia’ posato, non accetta

contestazioni dovute a vizi palesi visibili prima della posa finale (articolo, qualità,

tono, calibro, curvatura, macchie, etc.) e non risponde sulla qualita’ dell’opera

piastrellata finita ma solamente sulle caratteristiche del materiale fornito.

E’ bene pertanto conservare, al termine della posa, alcune piastrelle di scorta

per eventuali riparazioni, o anche per disporre di un campione rappresentativo

del materiale in caso di contestazione.

312